MOPAR A833 4-SPEED TRANSMISSION & COMPONENT SPECIALISTS

Bellhousing ballstud/bracket for 1976-80 Dodge truck small block applications with A833 overdrive, fits 10.5" overdrive bellhousing with casting number 3743859. Good used.

Reconditioned overdrive small block clutch fork, ball pivot style (Mopar part number 4210697), fits 1981-87 Slant 6 and V8 overdrive bell housings with casting numbers 4202506, 4202507 and 4202508, 13 1/8" overall length.

Reconditioned cluster gear for 1975-77 overdrive transmissions with high helix gearset. Tooth count 36-42-27-17R-17. Reference 3878651 T833-8F

Reconditioned cluster gear for 1977-up overdrive transmissions with 3.09 low gear ratio. Tooth count 33-37-27-17R-17. Pictured is version with 2 rings on cluster/1st gear. Reference 3878432 T833-8G

Good used countershaft for all overdrive transmissions 10.420" (see our CS-294 for 4-speed). Reference 4028123 T833-3A

Countershaft plug for all A833 overdrive transmissions. 1 per transmission.

Aluminum extension housing casting number C-13386/C-13364 A for A-body overdrive (only)transmissions with 26 spline output/307 bearing. Baked and bead blasted.

Clutch fork boot, correct for 1971 up vehicles, but will fit all models 1962 & up. For 1962 to 1970 exact concourse reproduction boot, use our FB021R.

Clutch fork pivot bracket for 1975 & up small block A/F-body cars with overdrive bellhousing casting number 3743859. OE 3743928

Clutch fork pivot bracket for cars needing to use short style (10 7/8" instead of 12 1/2") clutch fork with V8 overdrive bellhousing, casting number 3743859. Works for all 1966 to 1974 B & E body cars where the shorter fork is required. OE 3743929

Clutch fork pivot bracket for 1976-80 small block Dodge truck with overdrive bellhousing casting number 3743859, used with 12 1/2" long clutch fork (CF106R).

Good used clutch fork pivot bracket for 1976-80 small block Dodge truck with overdrive bellhousing casting number 3743859, used with 12 1/2" long clutch fork (CF106R).

Good used clutch fork pivot bracket for 1975 & up small block A/F-body cars with overdrive bellhousing casting number 3743859.

New clutch fork pivot ballstud, for ball pivot style clutch forks, as used in 1981-up A833 overdrive bell housings with casting numbers 4202506 and 4202507, 1981-up NP435 truck bell housing with casting number 4202508.

Floor tunnel fits late 70's to 1987 Dodge truck with A833 (overdrive), oval boot opening. Uses SB764N boot and SBB393 boot bezel. Good used.

Reverse detent housing base gasket, 1.150" outside/.875" inside diameters. 1 per transmission.

Premium bearing retainer gasket for all A883 4-speeds with #307 front bearing. This gasket is manufactured exclusively for Brewer�s Performance with a high performance matrix material, providing excellent flexibility, low flange pressure sealing, good bolt torque retention and reduced fluid wicking. Continuous temperature rated to 400 degrees Fahrenheit. This material DOES NOT require the use of ANY additional sealants. The use of additional sealants can cause the gaskets to squirm while torquing, thus resulting in a torn or damaged gasket!

Premium bearing retainer gasket for all A883 4-speeds with #308 front bearing. This gasket is manufactured exclusively for Brewer�s Performance with a high performance matrix material, providing excellent flexibility, low flange pressure sealing, good bolt torque retention and reduced fluid wicking. Continuous temperature rated to 400 degrees Fahrenheit. This material DOES NOT require the use of ANY additional sealants. The use of additional sealants can cause the gaskets to squirm while torquing, thus resulting in a torn or damaged gasket!

Backup light switch and/or reverse detent cap gasket, .925" outside/.565" inside diameters. 2 per transmission.

Premium extension housing (tail shaft) to main case gasket, for all A833 4-speeds. This gasket is manufactured exclusively for Brewer�s Performance with a high performance matrix material, providing excellent flexibility, low flange pressure sealing, good bolt torque retention and reduced fluid wicking. Continuous temperature rated to 400 degrees Fahrenheit. This material DOES NOT require the use of ANY additional sealants. The use of additional sealants can cause the gaskets to squirm while torqueing, thus resulting in a torn or damaged gasket!