MOPAR A833 4-SPEED TRANSMISSION & COMPONENT SPECIALISTS

New 29 tooth third gear for 1964-1970 23 spline transmissions with 2.66 ratio low gear. Reference 2464016 WT294-11

NOS Mopar 2464016 29 tooth third gear for 1964-up 23 spline transmissions with 2.66 ratio low gear. Reference WT294-11

NOS Mopar 2464659 27 tooth third gear for 1964-65 A-body and some early 70's 23 spline transmissions with 3.09 ratio low gear. One identification groove on tips of teeth. Reference WT294-11A

Reconditioned 27 tooth third gear for 1964-65 A-body and some early 70's 23 spline transmissions with 3.09 ratio low gear. One identification groove on tips of teeth. Reference 2464659 WT294-11A

Reconditioned 18 tooth fourth gear (overdrive gear) for 1975-up 23 spline overdrive transmissions with 3.09 ratio coarse pitch low gear. Reference 3878430 T833-11G

NOS 18 tooth fourth gear (overdrive gear) for 1975-up 23 spline overdrive transmissions with 3.09 ratio coarse pitch low gear. Reference 3878430 T833-11G

Reconditioned 20 tooth fourth gear (with one wide identifying mark on tooth tips), fits 1975-80 overdrive transmissions with 1st design high helix fine pitch. Reference 3878648 T833-11F

1963-67 AFB 4-Barrel Choke Assembly, Very nice reproduction of the 2264 580 choke assembly for 1963-67 Carter AFB equipped cars. "Lean" and "Rich" marks for adjustment. Yellow zinc dichromate and zinc finished parts as original. Includes carburetor attaching clip and correct mounting screws.

Foam axle retainer to backing plate gasket, all Dana 60 and 8 3/4 rearends, 2 required per car, sold each.

Metal axle housing to backing plate gasket, all Dana 60 and 8 3/4 rearends, 2 required per car, sold each.

Clutch adjusting rod grommet/insulator, fits all models.

Clutch adjuster kit for 1964-66 A-body Small block with 9.5” bellhousing. Includes adjusting rod, nut, washer, grommet, spring, clip/washer. Adjusting rod is 4 7/8" overall length

Clutch adjuster kit for 1962-65 B-body big block applications. Includes adjusting rod, nut, washer, grommet, spring, clip/washer. Adjusting rod is 4 7/8" overall length.

Clutch adjuster kit for 1967-1976 A-body small block applications, also 1975-up F-body. Includes adjusting rod, nut, washer, grommet, spring, clip/washer. Adjusting rod is 7 1/2" overall length.

Clutch adjuster kit for 1966-1979 B-body big or small block, 1970-4 E-body and 1971-4 B-body small block applications. (Should also be used in 1970-74 B/E big block applications when using 11" bellhousing and TS914 torque shaft). Also fits 1975-9 Chrysler Cordoba, 1975-8 Plymouth Sport Fury, 1977-8 Dodge Monaco, 1978-9 Dodge Magnum & 1979 Chrysler 300 Includes adjusting rod, nut, washer, grommet, spring, clip/washer. Adjusting rod is 4 7/8" overall length.

Clutch adjuster kit for 1970-1 E-body/1971-4 B-body big block applications, use with torque shaft TS913. (Will NOT fit 1970-74 B/E big block applications when using 11" bellhousing, use TS914 and AK449). Includes adjusting rod, nut, washer, grommet, spring, clip/washer. Adjusting rod is 4 7/8" overall length.

Clutch adjuster kit for original 1967-69 A-body big block applications, or conversion of any 1967-1976 A-body to big block. Includes adjusting rod, nut, washer, grommet, spring, clip/washer. Adjusting rod is 7 1/2" overall length.

Clutch adjuster kit for 1963-66 A-body small block applications using our 10.5" bell housing conversion parts. Use with TS636 torque shaft, BSB636 bell housing ball stud bracket, FP484 clutch fork pivot, and CF702 clutch fork. Includes adjusting rod, nut, washer, grommet, spring, clip/washer. Adjusting rod is 7 1/2" overall length.

Passenger's side rear axle locking pawl & nut, for all 1965 & up 8 3/4 and Dana 60 rear axles, holds the wheel bearing adjusting star in place after axle end play is set.

1966 & Earlier Big Block Engine w/o A/C - Fits water pumps with casting numbers 2205 862, 2468 007, & 2536 767. POWDER COATED black. Comes complete with (3) spacers, (4) OE correct bolts and (2) conical washers.